1. semi water cleaning and main water cleaning processes shall use solvent and double distilled water, plus a certain amount of surfactant, detergent and food preservative. This kind of cleaning is between solvent cleaning and water cleaning. Detergent belongs to solvent, flammable organic chemical solvent, high opening flash point, slight toxicity and safety factor, but the water must be cleaned after drying.

2、通過式噴淋清洗烘干線清水技術性清水技術是清水技術性的發展標底目地，務必創立清水和排水管道處理生產車間。

2. Clean water technology of through spray cleaning and drying line is the benchmark of the development of clean water technology. It is necessary to establish a production workshop for the treatment of clean water and drainage pipes.

3.在電焊焊接整個過程中運用無清除或無清理的焊錫膏，助焊膏馬上焊入下一個制作工藝清除，目前已不運用永久免費清除性作為替代性，十分是移動通信技術產品絕大多數是一次性的替代品。

3. In the whole process of electric welding, the solder paste without removal or cleaning is used, and the solder paste is immediately welded into the next manufacturing process for removal. At present, the permanent free removal specialty is no longer used as a substitute specialty, and most mobile communication technology products are disposable substitutes.

4、行業專用超聲波清洗機主要是實際操作溶劑的融解才可以除去污染物質。采用溶劑清洗，因為蒸發快，融解才可以強，因此機器設備規定樸素。

4. The special ultrasonic cleaning machine for the industry is mainly the actual operation of solvent melting to remove pollutants. Solvent cleaning is adopted, because the evaporation is fast and the melting can be strong, so the machinery and equipment regulations are simple.

（1）必須清洗超音波清洗槽中的線路板。隨后干預清水或溶劑清洗盤泡浸必須清洗的住所Z好是置放。

(1) The circuit board in the ultrasonic cleaning tank must be cleaned. Then intervene with clean water or solvent to wash the dish, soak the place that must be cleaned, and place it well.

（2）接入通過式噴淋烘干清洗線細致開關電源的電源，開啟電源總開關，運行超音波電源開關，設定工作時間，機械設備控制通?？烧{式020分鐘或開與關。數據控制可立即設置工作時間。

(2) Connect the power supply of the fine switching power supply of the through spray drying and cleaning line, turn on the main power switch, run the ultrasonic power switch, set the working time, and the control of mechanical equipment is usually adjustable for 020 minutes or on and off. Data control can set working hours immediately.

（3）設定好工作時間后，清洗機希望1至5min后Z開始工作中，清洗機將積極完畢工作中，假如您開啟清洗機作用一切正常開啟或工作時間太長，立即帶清洗電腦主板就可以。

(3) After setting the working time, the cleaning machine hopes that Z will start working in 1 to 5 minutes, and the cleaning machine will actively complete its work. If you turn on the cleaning machine, everything will start normally or the working time is too long, you can immediately bring the cleaning computer motherboard.

通過以上的內容我們應該對于超聲波清洗設備http://www.xgsic.com內容有了一定的了解，更多的精彩內容請繼續關注我們的網站及相關資訊/

Through the above content, we should be for ultrasonic cleaning equipment http://www.xgsic.com With a certain understanding of the content, please continue to pay attention to our website and related information for more wonderful content/